Profesionāla būvmateriālu komplektācija un pārdošana Baltijas valstīs
Siltinātas paneļu sistēmas ārējām un iekšējām sienām nodrošina ļoti augstu izturību pret uguni un karstumu un labu konstrukcijas veiktspēju.
Mēs piedāvājam risinājumus telpām ar individuālām prasībām, piemēram, papildu ugunsdrošību, higiēnu, jutīgu akustiku un modernu arhitektūru.
Sendvičpaneļu risinājumi ietver visu nepieciešamo konstrukcijas pabeigšanai: paneļus, stiprinājumus, apšuvumus, profilus.
Sandwich panels with a MAX core (with lambda 0.019): insPIRe S MAX / insPIRe U MAX / insPIRe CH MAX
To meet the needs and challenges of the market our manufacturer, as one of the few manufacturers created sandwich panels with a PIR MAX core with 0.019 lambda. These are currently the best thermal insulation parameters on the market compared to other products of this type.
Construction standards which will apply from 2021 will pay off with significantly lower energy consumption and comfort of use. Lower energy consumption also means less emissions, and therefore cleaner air and a slower greenhouse effect. The use of panels with a MAX core gives a lot of benefits. We gain more space through thinner walls, which allow the building line to be moved closer to the plot border, we also gain a larger usable area inside the hall. Remember that with large halls, each additional centimeter gives additional space. Another undoubted advantage is the excellent thermal insulation, that means real energy savings and operating costs of the building.
insPIRe® S MAX
NEW! Polyisocyanurate wall panel
insPIRe® S MAX wall panels are designed for external curtain walls and internal partition walls in skeletal structures. The panels can be installed both vertically and horizontally as single and multi-span wall elements. The plate cladding is galvanized steel sheet on both sides according to EN 10346 with organic polyester varnish with a coating thickness of 25 μm. The tightness of panel joints is ensured by the PUS polyurethane gasket applied at the production stage.
insPIRe® U MAX
NEW! Polyisocyanurate wall panel
insPIRe® U MAX wall panels are designed for external curtain walls and internal partition walls in skeletal structures. The panels can be installed both vertically and horizontally as single and multi-span wall elements. Hidden fastening, invisible from the facade, makes these panels very attractive in terms of architecture and functionality. The plate cladding is galvanized steel sheet on both sides according to EN 10346 with organic polyester varnish with a coating thickness of 25 μm. The tightness of panel joints is ensured by the PUS polyurethane gasket applied at the production stage.
MW S
NEW Wall panel with a mineral wool core
MW S wall panels with visible fastening are intended for the construction of external and internal walls on a building frame. Steel sheet galvanized on both sides according to EN 10346 and coated with an organic polyester coating with a coat thickness of 25 μm is used as facing. The panels can be installed both in a vertical and horizontal arrangement. They ensure maximum fire protection and excellent sound reduction
MW U
NEW Wall panel with a mineral wool core
MW U wall panels are intended for the construction of external and internal walls on a building frame. Concealed fasteners, which cannot be seen if viewed from the facade, contribute to panels being architecturally attractive and functional. Steel sheet galvanized on both sides according to EN 10346 and coated with an organic polyester coating with a coat thickness of 25 μm is used as facing. The panels can be installed both in a vertical and horizontal arrangement. They ensure maximum fire protection and excellent sound reduction.
insPIRe® FIRE CH
NEW! Polyisocyanurate cooling panel PIR EI 60 Fire spread B-S1, d0
Sandwich panel with increased fire resistance class insPIRe® FIRE consists of 2 galvanized steel claddings and coated with organic polyester varnish. The core consists of two layers of PIR foam manufactured according to proprietary procedures. The fire resistance class EI 60 allows to obtain a properly shaped panel lock additionally sealed with a rock wool element.
MODUĻA PLATUMS
- stiprināmais panelis: 1000mm un 1140mm
- slēptā stiprinājuma panelis: 1000mm
PROFILĒJUMS:
Ārējais profilējums: Linear, Microfiltered, Wavy, Grooved, Flat
Iekšējais profilējums: Linear, Flat
KRĀSAS
Standarta ārējās apdares krāsas
RAL 3000
RAL 8017
RAL 5010
RAL 6011
RAL 9002
RAL 9006
RAL 7016
RAL 9007
RAL 7035
RAL 9010
Standarta iekšējās apdares krāsas
RAL 9002
RAL 9010
USAGE
OUTER WALL - HORIZONTAL ARRANGEMENT OF PLATES
-
insPIRe® S sandwich panel
-
Construction screw
-
Polyethylene sealing tape (PES)
-
Flashings the foundations
-
Plate flashing
-
Corner flashing
-
Construction of the object
The use insPIRe® S sandwich panels with visible fastening is a solution optimized for economic and strength reasons. The availability of panels in two modular widths minimizes the waste generated during assembly.
OUTER WALL - VERTICAL ARRANGEMENT OF PLATES
The use of insPIRe® U sandwich panels with invisible fastening improves the visual effect of the building's facade. In addition, the use of flashings offered by Gór Stal and dedicated mounting accessories facilitates panel assembly and finishing works.
-
insPIRe® U sandwich panel
-
Construction screw + washer PM-1
-
Polyethylene sealing tape (PES)
-
Flashings the foundations
-
Corner flashing
-
Construction for sandwich panels
-
Construction of the object
PARTITION WALL - VIEW FROM THE SIDE OF THE PLATES
The low tare weight of sandwich panels facilitates their installation in closed rooms, where transport of panels by mechanical means is difficult or even impossible. In addition, a wide range of typical flashings, as well as the ability to perform machining according to an individual project allows you to meet customer requirements.
-
insPIRe® S sandwich panel
-
Construction screw
-
Polyethylene sealing tape (PES)
-
Flashings for joining panels to the floor
-
Plate flashing
-
Construction for the inner wall
CEILING - BOTTOM VIEW
-
insPIRe® S sandwich panel
-
Construction screw
-
Polyethylene sealing tape (PES)
-
Plate flashing
-
Flashing the connection of panels with the wall
-
Ceiling construction
The low tare weight of sandwich panels facilitates their installation in closed rooms, where transport of panels by mechanical means is difficult or even impossible. In addition, a wide range of typical flashings, as well as the ability to perform machining according to an individual project allows you to meet customer requirements.
CEILING - TOP VIEW OF THE STRUCTURE
The low tare weight of sandwich panels facilitates their installation in closed rooms, where transport of panels by mechanical means is difficult or even impossible. In addition, a wide range of typical flashings, as well as the ability to perform machining according to an individual project allows you to meet customer requirements.
-
insPIRe® S sandwich panel
-
Construction screw
-
Polyethylene sealing tape (PES)
-
Plate flashing
-
Flashing the connection of panels with the wall
-
The ceiling structure is adapted to the mounting conditions of the panels
INSTALLATION OF PANELS
Sandwich panels are a commonly used building material for light external envelope cladding of industrial halls, warehouses and production buildings, department stores and commercial facilities, office buildings, administrative buildings and cold storage facilities. Installation of sandwich panel can be performed in almost any weather conditions.
PAPILDUS MATERIĀLI
GASKETS AND OTHER ACCESSORIES
-
Gaskets for sandwich panels
-
Sealing flanges intended for passage of ducts (e.g. ventilation) through the casing made of sandwich panels
-
Bushings - washers for cold plates
We supply adhesive, polyurethane (PUS and PURS), polyethylene (PED) and butyl sealing tapes
SELF DRILLING SCREWS:
-
for hot rolled construction (wall thickness from 3 to 12 mm)
-
for cold-bent construction (thickness from 1.5 mm to 5 mm)
On special order it is possible to provide caps or connectors in the color of the outer cladding of the sandwich panel. Panels can be joined to steel, reinforced concrete and wooden constructions using dedicated fasteners. Detailed information on connectors can be found in our technical catalogues.
FLASHINGS
-
Length: 3000 mm or 6000 mm
-
Material: galvanized steel sheet
-
Protective coating: polyester varnish
-
Additional protection: foil
Manufacturer has a profiling machine that allows bending of 1.25 mm thick sheet metal (maximum length of 6 m), in typical shapes from the catalog and according to the individual design of the customer. Detailed information on sheet thickness and colors can be found in the catalog dedicated to a specific panel.
The flashings are protected against damage by foiling the top side. Detailed data is available in the section "For designers - flashing"
Steel flashing are part of the insulation panel system - Sandwich Panels.
Additionally, they are used as a separate decorative element.
Steel flashing is made of galvanized metal sheet with a thickness of 0.5 mm, 0.7 mm and 1.0 mm, colors according to the RAL palette.
Standard length of metal flashing sheet is 6.0 m.
Contact us for detailed information regarding specific panel thickness, span and type of application.